Installing A Bath tub
Installing A Bath tub
Blog Article
The author is making a few great pointers about A Step-by-Step Guide to Installing a Bathtub overall in this article further down.
Mounting a tub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a new one is additionally a reasonably difficult project. If the old bathtub is conveniently available, the project can move immediately; if you need to open up a wall surface to get rid of the old tub and also position the new bathtub, the job is a lot harder. In either instance, the task is within a residence handyman's abilities, although you will certainly require an assistant to move out the old bathtub and set in the brand-new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is much better to think about utilizing one before you begin. Chances are you may require a specialist plumber to make tube links.
This post will help you mount a brand-new bath tub in your restroom if you have currently acquired a brand-new bathtub as well as don't need to transform the setup of your previous water pipes.
Your tools and product list must make up the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly troublesome because of the restricted access that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from turning throughout this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to moving on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end supplies a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need lowering couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washers remain in place between the faucet and the sink. Protect the faucet in place with the maker given backnut. Once the faucet is firmly in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The former type needs to be connected to the tap finishes initially, tightening up just by hand. The supply pipes can later be linked to the various other end. Tighten both ends with a spanner after both ends have been linked.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the needed setting. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The following objective is to ensure that the tub is leveled all round. This can be accomplished by examining the spirit level as well as readjusting the feet on the bath tub till the spirit level reads level.
To set up taps, fit all-time low of the outermost adaptable faucet port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Switch on the supply of water and inspect all joints as well as new pipework for leaks as well as tighten them if needed. Fill up the tub as well as additionally examine the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling and sealing around the bathtub should wait until the bathtub has been used at the very least when as this will certainly resolve it right into its last setting.
Getting ready for the Installation
Firstly, the supporting frame provided with the bathroom must be fitted (if needed) according to the maker's directions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is very important to make certain that if the tap comes with a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps unit to stop stress on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet through the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. See to it you utilize every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its last placement.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move sufficient to break a rigid seal, creating the water to permeate the wall surface in between the bath and also the tiling, resulting in complications with wetness and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components and installations. They are offered in tubes and cartridges, and also can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill up the bath tub with water prior to sealing, to permit the movement experienced when the bathtub is in usage. The sealant can fracture relatively early if you do not think about this motion prior to sealing.
Alternatively, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also conveniently available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant glue as well as cement.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
As a keen person who reads about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I was thinking sharing that post was mandatory. Remember to take the time to promote this blog if you appreciated it. We treasure reading our article about Installing A Bathtub.
Get Started
Report this page